KNITTING DENSITY
16 p. X 26 p. = 10 x 10 cm, is connected by a garter stitch on the needles No. 7.
IMPORTANT!
To get the product acc. size, the density of your knitting should correspond to a given, primarily in width. Therefore, before starting to work, you should tie a pattern sample: dial 26 points and knit 14 cm garter stitch. Then count the loops in the middle section of the fabricated sample with a length of 10 cm: if there are more than 16 loops in this segment, change the spokes to thicker ones, if less - to thinner ones.
If the instruction contains only one number, it applies to all sizes.
COMPLETING OF THE WORK
BACK
On the needles No. 7, dial 93 (99) 105 points and knit a garter stitch, while at 31 points in the middle of the back to the end of the detail, knit with a “Veer” pattern according to the scheme (1st row = wear row).
Attention!
In each 18th row, according to the pattern scheme, perform side reductions as follows: 2 persons, 2 points, knit together the face, knit to the last 4 points of the row, then 2 points, knit together the face with an inclination to the left, 2 faces.
In height, repeat the repeat of the “Fan” pattern 9 times, knit the first 9 (5) 1 p. next rapport, then close the loop for armholes and start raglannyh downs. To do this, on both sides at the beginning of each row close for the armholes 2, 2 p., In the next row (= persons. Row), perform the subtract reductions: 1 person., 2 points. , 2 p. Knit together the front with a tilt to the left, 1 person.
Regular reductions are repeated in each row of persons. sides up to the 18th row = repeat of the “Fan” pattern in height only 12 times.
In the next row with izn. the parties to close the remaining 25 (27) 29 p.
BEFORE
Knit as back.
SLEEVES
On the needles number 7, dial 39 (43) 47 p. And knit garter stitch, while at 31 p. In the middle of the part until the end of work to knit the pattern "Fan" according to the scheme (1st row = izn. Row).
Attention!
After 9 p. on the 2nd rapport of the pattern, make on both sides for bevels after / before 2 chrome. on 1 nakidu = in a trace. twist the row 3 times before knitting it with the front. These additions are repeated 9 times in each 8th p.
Knit 5 rapports of the “Fan” pattern in height, then 9 (5) 1 p. next rapport, close the loop for armholes and start raglannyh downs. For armholes close on both sides at the beginning of each row 2, 2 p., Knit 2 p. directly and in the next row (= persons. row), perform the slow downs: 1 person., 2 points. knit together the face, knit up to the last 3 points of the row, 2 points. knit together the face with a slope to the left, 1 person. These raglannyh downgrades are repeated in every 2nd row of faces. sides, both on the back and in front.
Knit 18 p. from the start of the raglan downs = repeat of the “Fan” pattern in height, repeat 8 times from the start of the sleeve and in the next row from the outside. the parties to close the remaining 25 (25) 25 p.
ASSEMBLY
The parts should be connected to the front side with a mattress seam and a “loop in a loop” seam: with a mattress one — vertical edges of the parts (= 1 p. Of one piece with 1 p. Other), a “loop in a loop” seam — edges with closed loops.
Run side seams and sleeve seams.
Sew the bottom edges of the armholes and rounds and perform the seamed seams Collar: on the needles number 5 with persons. hand work (thread at work) dial on the edge of the neck on 1 p. from each closed loop = 92 (96) 100 p.
Knit the collar 6 cm with a rubber band in a circle: alternately 1 person., 1 outer.