CLOSING LOOP NEEDLE
Leave the end of the thread approx. 100 cm and put in an embroidery needle for wool.
Step 1: insert the needle into the 1st loop from the seamy side to the front one and stretch the thread.
Step 2: skip 1 loop, insert the needle into the 3rd loop from the front side to the wrong side and stretch the thread.
Step 3: insert the needle into the 2nd (missed) loop from the seamy side to the front one, at the same time withdraw the needle under the thread stretched in front of the loop. Stretch the thread.
Step 4: insert the needle into the 4th (through one from the 2nd) loop from the front side to the wrong side and stretch the thread.
Step 5: insert the needle from the seamy side to the front one into the 3rd (missed) loop, in so doing withdraw the needle over the thread stretched in front of the loop and stretch the thread.
Continuously repeat steps 2–5 until all loops are closed.
KNITTING DENSITY
23 p. X 32 p. = 10 x 10 cm, connected by the front surface;
29 p. X 34 p. = 10 x 10 cm, connected by an openwork pattern.
Pattern
COMPLETING OF THE WORK
BACK
Dial 118 (128) 138 loops with a cross set and, for a strap, tie 6 cm = 20 rows with an elastic band A.
Continue the work with the front satin stitch.
After 31 cm = 100 rows from the plate, close for the armholes on both sides 1 x 4 points and after 32 cm = 102 rows from the plate leave the remaining 110 (120) 130 points.
LEFT SHOT
Dial the needles with 60 (66) 72 loops with a cross-shaped set and knit the strap as follows: edge, 56 (62) 68 sections with an elastic band A, while starting from edge, start with 1 wrong, 3 sections of the patent edge.
After 6 cm = 20 rows from the beginning of the knitting of the plank, continue the work as follows: edge trim, 46 (52) 58 n. Front satin stitch, 10 n. Pattern 1 and 3 n. Continue knitting the patent edge (= shelf strip).
Attention: 10 p. Slats of the ledge and 3 p. Of the patent edge on the pattern are 4 cm.
Close 31 cm = 100 rows from the slider to close the armhole on the right edge 1 x 4 n.
After 32 cm = 102 rows from the slat, leave the remaining 56 (62) 68 p.
RIGHT SHELL
Knit the same as the left shelf, but in a mirror image, and with 3 holes for buttons. For each button hole after 3 sts of the patent edge and 3 sts of gum A, close the next 3 loops and dial again in the wrong side.
The lower buttonhole should be made 2 cm = 6 rows from the initial row, the next two button holes should be made at intervals of 14.5 (15) 15.5 cm.
SLEEVES
Dial 56 (62) 68 loops for each sleeve with a cross set and, for a strap, tie 6 cm = 20 rows with an elastic band A.
Continue the work of the facial surface.
For the bevel of the sleeves, add on both sides in each 14th row from the bar 3 x 1 par. And in each 10th row 6 x 1 par. (In every 14th row 4 x 1 par. And in every 8th row row 6 x 1 p.) in each 14th row 3 x 1 p. and in every 8th row 8 x 1 p. = 74 (82) 90 p.
35.5 cm = 114 rows from the bar close for armhole on both sides 1 x 4 p.
After 36.5 cm = 116 rows from the strip leave the remaining 66 (74) 82 p.
ROUND COQUETTE
The hinges of the right wing, 1st sleeve, back, 2nd sleeve and left shelf alternate between circular needles No. 4.5 = 354 (392) 430 p.
Attention: only alternate patterns on the middle loops, external by 3 loop patent edge and 10 p. slat shelves on both sides continue to knit acc. patterned.
On the middle 328 (366) 404 loops, tie 1 cm = 2 rows (2 cm = 6 rows) 3 cm = 10 rows by the front satin stitch, while evenly distributing, add 1 (2) 2 rows on the shelves ., on the sleeves at 0 (1) 3 points and on the back 1 (3) 5 points = 331 (375) 419 medium loops.
On the middle hinges, continue the work with an openwork pattern, at the same time perform reductions, starting with the 53rd row of the pattern according to pattern.
At the same time, 7 cm = 22 rows (8 cm = 26 rows) 9 cm = 30 rows from the beginning of the knitting of the yoke to execute one more hole for the button in the plank of the right shelf.
After 19 cm = 64 rows (20 cm = 68 rows) 21 cm = 72 rows from the start of the yarn knitting, 211 (239) 267 loops of the openwork pattern will remain.
On these hinges, continue work for the neck strip as follows:
1st row: * 1 front, 2 back, from * perform only 70 (79) 88 times, finish 1 face, (1 front, 1 back) 1 front, 1 back , 1 facial.
2nd and 4th rows: knit loops according to the pattern.
3rd row: * knit 2 loops together with a tilt to the left (= remove the front loop as the front loop, knit the next loop face and stretch it through the removed loop), 1 purl, from * complete only 70 (80) 90 times, finish 1 (0) 1 face = 141 (159) 177 p.
After 1.5 cm = 4 rows from the beginning of the knitting of the plank, continue work on all the loops with pattern 3, while continuing the eraser A of the slats, middle loops are now included in the knitting rhythm.
At the same time, in the 5th row of the ledge on the right shelf, make another button hole over the previous ones.
With a width of 3 cm = 10 rows, close all the loops with a needle as described.
ASSEMBLY
Run side seams and sleeve seams.
Buttonhole holes wrap stitched seam. Sew buttons.
Photo: magazine "Sabrina" №8 / 2017