A tight skirt is quite simply knitted and sits perfectly thanks to the zip fastener on the back.
Yarn (59% cotton, 41% viscose, 105 m / 50 g) - 300 (350) 400 g yellow and 300 (350) 400 g sulfur; Elastic braid width of 2 cm of appropriate length for the waist; hook number 4.
Knit in the circular rows acc. scheme. Start with loops before the rapport, repeat constantly repeat, finish 1 connection. Art. in the first loop of a circular row. 2-5th circle rows constantly repeat, at the same time start with a yellow thread and knit on 4 rows alternately with a gray thread. Each round-the row finish 1 connection. Art.
"THE CORRUPT STEP"
Art. b / n perform in the direction from left to right.
DENSITY OF ABRASION
16 p. X. 20 p. = 10 x 10 cm.
ATTENTION!
Since the number of loops in the pattern varies, it is recommended to make for all parts a paper pattern in the original size and perform the reduction and addition in accordance with our data acc. pattern. To do this, the workpiece to be constantly applied to the pattern.
PATTERN
COMPLETING OF THE WORK
With a gray thread execute a chain of 145 (153) 163 bp, close it with the help of 1 connection. Art. in a ring and tie 2 cm of st. b / n.
Then knit with a colored pattern with elongated loops.
After 27 (28) 30 cm from the initial row, perform lateral depressions acc. pattern.
After 47 (48) 50 cm from the initial row, another 2 cm of st. b / n gray thread, then the work is finished.
ASSEMBLY
The skirt is slightly moistened, stretched according to the dimensions indicated on the pattern and left to dry completely.
Carry out side seams. From the wrong side, sew the elastic band to the waistband.
ATTENTION!
This skirt can be worn with a striped jacket with narrow slats
Striped Jacket with narrow slats
Due to the loops tying into the puncture, an unusual striped effect is created. Especially elegant look narrow, connected by columns, without a cape, gray bars.
DIMENSIONS
36/38 (40/42) 44/46
YOU WILL BE REQUIRED
Yarn (59% cotton, 41% viscose, 105 m / 50 g) - 450 (500) 550 g yellow and 450 (500) 550 g sulfur; 5 gray buttons; hook number 4.
PATTERNS AND SCHEMES
COLOR PATTERN WITH HOLE LOTS AT 2 PI.
Knit in the rows of direct and reverse directions acc. scheme. Turning rows, as indicated.
Start with the loops before the rapport, repeat constantly repeat, end with the loops after the rapport. Run 1-5th row 1 time, 2-5th row constantly repeat, at the same time start with a yellow thread and knit on 4 rows alternately with a gray thread.
"THE CORRUPT STEP"
Art. b / n perform in the direction from left to right.
DENSITY OF ABRASION
16 p. X. 20 p. = 10 x 10 cm
ATTENTION!
Since the number of loops in the pattern varies, it is recommended to make for all parts a paper pattern in the original size and perform the reduction and addition in accordance with our data acc. pattern. To do this, the workpiece to be constantly applied to the pattern.
PATTERN
COMPLETING OF THE WORK
BACK
Execute a chain of 81 (87) 93 bp. and tie 2 cm of st. b / n gray thread.
Then knit with a colored pattern with elongated loops.
After 53 (55) 57 cm from the initial row, leave the middle 25 pips for the cutout of the necks unbroken and finish both sides separately, while in the second row from the side of the cut, 1 x 3 p.
After 55 (57) 59 cm from the initial a number of work to finish.
LEFT STICK
Execute a chain of 39 (43) 45 bp. and tie 2 cm of st. b / n gray thread.
Then knit with a colored pattern with elongated loops.
After 43 (45) 47 cm from the initial row, leave the left edge for the cutout of the neck 1 x 10 (11) 10 n. Unprinted, then on the side of the cutout, subtract in each 2-nd row 1 x 2 n. And 2 x 1 n.
After 55 (57) 59 cm from the initial series of work to finish.
RIGHT STICK
Knit in mirror image.
SLEEVES
Execute a chain of 33 (35) 39 bp, tie 2 cm of st. b / n with a gray thread and then knit with a colored pattern with elongated loops.
For bevels, add 5 (5) 8 x 1 n. On each side and in each 4th row on each side of the 6th row. 13 (14) 10 x 1 n.
After 45 (47) 49 cm from the beginning of the series finish the work.
ASSEMBLY
The details should be slightly moistened, stretched according to the dimensions indicated on the pattern and left to dry completely. Perform shoulder seams.
The front edges of the shelves and the neckline are tied with a gray thread of 2 cm st. b / n, while in the 2 nd row, make in the bar of the right shelf 5 holes for buttons. To do this, after 5 cm from the initial row, make the first hole for the button (3 lines of the previous row and skip 3 turns) and at intervals of 6 (7) 7 cm make the remaining 4 holes for the buttons. For the corners of the neck cut, tie in the uppermost loop of the front edges in each row of 2 tbsp. b / n.
Sew off the buttons.